Green Onyx Stone Tables - Dining, Coffee, Console & Side Tables

The Pain Point: Matched Table Sets That Do Not Actually Match

If you furnish hotel restaurants, executive lounges or a furniture retail program with natural onyx, you already know the failure mode. You order a set — a green onyx dining table for the main room, onyx coffee tables for the lounge, a console table for the entrance — and the tops arrive cut from three different blocks. The vein direction runs one way on the dining top and another on the coffee tables. One top reads a deeper green under showroom lighting, another turns pale the moment an LED panel goes behind it. The set was quoted, shipped and invoiced as one order, but on the floor it looks assembled from leftovers.

This is the single most common complaint buyers raise about onyx tabletop programs, and it is not a machining problem. It is a sourcing and planning problem: most workshops carve each tabletop from whatever block is nearest at hand, because block-level planning costs time up front.

What This Costs You as a Buyer

• Project rejection: hospitality fit-out teams measure tops against approved samples. A mismatched set fails inspection, and the replacement cycle restarts at the back of the queue.
• Margin erosion: remaking a carved 30 mm onyx top means new raw block, new machine hours and new freight — costs that land on you if your contract does not pin the root cause on the supplier.
• Timeline slip: a remake of a whole set typically pushes your installation window past the FF&E handover date, and liquidated damages clauses start to bite.
• Lost showroom sales: retail buyers compare pieces side by side. A set with visible tonal and vein mismatch simply does not sell at onyx pricing.

Our Solution: One Vein Plan for Every Top in the Set

Apexstone treats a table program the way a stonemason treats a bookmatched wall: as one allocation plan, not a pile of separate orders. Before any cutting starts, we select the blocks that will supply the whole set, map the veining on each raw slab, and assign each tabletop a position in the plan — so the dining top, the coffee tables and the console top read as one continuous story of green and gold.

Because green onyx is a translucent stone, the plan also covers light behavior. Where tops will sit over LED backlighting, we check translucency slab by slab during allocation, so a set lit from below glows evenly instead of patchy.

The Process Behind It

• Block-level selection: tops for one program are allocated from matched blocks before cutting, not after.
• Vein mapping and layout: each raw slab is photographed and vein-mapped; we confirm the layout direction with your drawings before the first cut.
• CNC contour fabrication: round, oval, rectangular, square and fully custom outlines are cut on CNC centers so the shape matches your drawing exactly, including cut-outs for table hardware.
• Unified edge detailing: all tops in a set receive the same profile — eased, beveled, chamfered, bullnose or ogee — so the set is consistent to the touch as well as the eye.
• Thickness options of 18 mm, 20 mm and 30 mm, held to specification across the set so seat heights and table frames line up.
• Finish control: high-gloss polished is standard; honed is available on request where your design calls for a matte surface.
• Backlight check: tops destined for illuminated bases are reviewed for translucency consistency before packing.

Green Onyx Tabletop Specifications

Fabrication Capacity You Can Plan Around

Onyx is unforgiving material: it is softer and more brittle than granite, and a careless edge pass can chip a finished top beyond repair. Our tabletop line is set up specifically for this risk profile. Contour cutting runs on CNC machining centers rather than hand tracing, so the hundredth tabletop in a rolling program matches the first as closely as the second. Edge profiling is performed after contouring on the same fixture, which keeps profiles concentric with the outline instead of drifting. Each top passes a surface inspection under raking light for polish quality, chips and natural fissure handling before it is crated.

For furniture brands, this means you can add new shapes to an existing program without re-qualifying the whole set: the vein plan, edge language and finish standard carry over. For hospitality procurement, it means tops for a phase-two restaurant can be produced to match phase one, provided the vein plan and block allocation are recorded at the time of the original order — which is exactly why we document every program we run.

Frequently Asked Questions

Can you match my approved sample across a full set?

Yes — that is the core of our vein-plan workflow. Send us the approved sample or its photos; we allocate blocks and map veining for the entire set before cutting and confirm the layout with you in writing.

What do you need from us to start production?

Drawings with dimensions, shape, edge profile and thickness, plus the finish choice (polished or honed). The 25–35 day lead time starts once drawings are approved.

Is green onyx suitable for daily-use dining tables?

Green onyx is a natural stone and needs reasonable care — coasters, prompt wipe-downs and no abrasive cleaners. Many restaurants and hotel programs use it successfully with that understanding; we are happy to discuss care guidance for your end users before you order.

Can tops be backlit?

Yes. Translucency is one of green onyx's defining features, and our standard process includes a translucency consistency check for tops intended for LED bases. Lighting hardware is specified by your design team; we confirm slab suitability for the effect.

What is the MOQ and how are tops packed?

MOQ is 5 pieces. Tops are packed in foam-lined wooden crates with face protection; packing is designed around the brittleness of onyx edges.